Purpose Polymers typically have intrinsic thermal conductivity much lower than other materials. Enhancement of this property may be obtained by the addition of conductive fillers. Nanofillers are preferred to traditional ones, due to their low percolation threshold resulting from their high aspect ratio. Beyond these considerations, it is imperative that the development of such new fillers takes place in a safe and sustainable manner. A conventional life cycle assessment (LCA) has been conducted on epoxy-based composites, filled with graphite nanoplatelets (GnP). In particular, this study focuses on energy requirements for the production of such composites, in order to stress environmental hot spots and primary energy of GnP production process (nano-wastes and nanoparticles emissions are not included). Methods A cradle-to-grave approach has been employed for this assessment, in an attributional modeling perspective. The data for the LCA have been gathered from both laboratory data and bibliographic references. A technical LCA software package, SimaPro (SimaPro 7.3), which contains Ecoinvent (2010) life cycle inventory (LCI) database, has been used for the life cycle impact assessment (LCIA), studying 13 midpoint indicators. Sensitivity and uncertainty analyses have also been performed. Results and discussion One kilogram of GnP filler requires 1,879 MJ of primary energy while the preparation of 1 kg of epoxy composite loaded with 0.058 kg of GnP 303 MJ. Besides energy consumption in the filler preparation, it is shown that the thermoset matrix material has also a nonnegligible impact on the life cycle despite the use of GnP: the primary energy required to make epoxy resin is 187 MJ, i.e., 62 % of the total energy to make 1 kg of composite. Conclusions Raw material extraction and filler and resin preparation phase exhibit the highest environmental impact while the composite production is negligible. Thermosetting resin remains the highest primary energy demand when used as matrix for GnP fillers. The result of the sensitivity analysis carried out on the electricity mix used during the GnP and the composite production processes does not affect the conclusions.

Microporous AlPO4-54·xH2O, which exhibits the largest pores among zeolites and aluminophosphates with a diameter of 12.7 Å, was investigated at high pressure by X-ray powder diffraction and Raman spectroscopy in diamond anvil cells. The material was found to begin to amorphize near 2 GPa using either a nonpenetrating pressure transmitting medium (PTM) silicone oil or no PTM. When H2O is used as a PTM, amorphization begins at a lower pressure of 0.9 GPa. In this case, superhydration effects are observed and higher relative unit cell volumes are observed prior to the beginning of pressure-induced amorphization (PIA) as compared to the experiment in silicone oil due to insertion of the H2O molecules in the pores. In all cases, in these experiments at room temperature, amorphization was irreversible. Ex situ experiments were used to investigate the local structure of pressure-amorphized AlPO4-54·xH2O by nuclear magnetic resonance and by X-ray absorption spectroscopy, which show that, upon increasing pressure, two water molecules enter in the coordination sphere of IVAl, thereby increasing the coordination number from 4 to 6, which destabilizes the structure. The present results show that the insertion of and/or reaction with guest species can be used to strongly modify the stability of microporous materials with respect to PIA.

We have investigated the phonon modes of Ag-3[Co(CN)(6)] using first-principles based methods and high-pressure infrared spectroscopy to understand the origin of its colossal thermal expansion. Griineisen parameters of its zone-center vibrational modes were obtained from the calculations and compared to the experimental ones. We found that optical phonon modes below 100 cm(-1) mainly contribute to its negative thermal expansion, and they also have a significant mixing with acoustic branches. These modes have been assigned to translational motion of the Co-CN-Ag-NC-Co linkages. We also identify a pressure-induced softening of zone-center phonon modes that could account for the experimentally observed phase transition in terms of a first-order displacive instability from the trigona1P-3-1m space group to the acentric Cm space group.

Photo-active molecules are confined into single-wall carbon nanotubes to create 1D hybrid systems with new and original opto-electronic properties. This work deals with the encapsulation of quaterthiophene derivative and phthalocyanine molecules. They display strong optical absorption in the visible range, respectively around 400 and 670 nm. Encapsulation efficiency is investigated through Transmission Electron Microscopy. The physical interactions are mainly investigated by optical spectroscopies. The Raman spectra of the oligothiophene hybrid systems exhibit a striking dependence with the excitation energy which is correlated to the optical absorption energy of the photo-active molecule. Close to the molecule resonance, the results suggest a significant photo-induced charge transfer between the photo-active molecules and the nanotubes. In addition, the resonance window of the confined molecules depends on the nanotube diameter. The Raman spectra of the phthalocyanine based systems depend on the optical resonance conditions of the encapsulated molecules and on the structural properties of the hybrid system.

The self-assembly of a bis-urea phenylene-bridged silsesquioxane precursor during sol-gel synthesis has been investigated by in situ infrared spectroscopy, optical microscopy and light scattering. In particular, the evolution of the system as a function of processing time was correlated with covalent interactions associated with increasing polycondensation and non-covalent interactions such as hydrogen bonding. A comprehensive mechanism based on the hydrolysis of the phenylene-bridged organosilane precursor prior to the crystallization of the corresponding bridged silsesquioxane via H bonding and subsequent irreversible polycondensation is proposed.

1D-confinement of polyiodides inside single-wall carbon nanotubes (SWCNT) is investigated. Structural arrangement of iodine species as a function of the SWCNT diameters is studied. Evidence for long range one dimensional ordering of the iodine species is shown by X-ray and electron diffraction experiments independently of the tube diameter. The structure of the confined polyiodides is investigated by X-ray absorption spectroscopy. The confinement influences the local arrangement of the chains. Below a critical diameter Fc of 1 nm, long linear polyiodides are evidenced leading to a weaker charge transfer than for nanotube diameter above Fc. A shortening of the polyiodides is exhibited with the increase of the nanotube diameter leading to a more efficient charge transfer. This point reflects the 1D-confinement of the polyiodides inside the nanotubes.