Low-dimensional materials have been examined as electrocatalysts for the hydrogen evolution reaction (HER). Among them, two-dimensional transition metal dichalcogenides (2D-TMDs) such as MoS2 have been identified as potential candidates. However, the performance of TMDs toward HER in both acidic and basic media remains inferior to that of noble metals such as Pt and its alloys. This calls for investigating the influence of controlled defect engineering of 2D TMDs on their performance toward hydrogen production. Here, we explored the HER activity from defective multilayered MoS2 over a large range of surface S vacancy concentrations up to 90%. Amorphous MoS2 and 2H MoS2 with ultrarich S vacancies demonstrated the highest HER performance in acid and basic electrolytes, respectively. We also report that the HER performance from multilayered MoS2 can be divided into two domains corresponding to "point defects" at low concentrations of surface S vacancies (Stage 1) and large regions of undercoordinated Mo atoms for high concentrations of surface S vacancies (Stage 2). The highest performance is obtained for Stage 2 in the presence of undercoordinated Mo atoms with a TOF of similar to 2 s(-1) at an overpotential of 160 mV in 0.1 M KOH which compares favorably to the best results in the literature. Overall, our work provides deeper insight on the HER mechanism from defected MoS2 and provides guidance for the development of defect-engineered TMD-based electrocatalysts.

Silica-wollastonite xerogel composites (xerocomposites) with different wollastonite filler content were obtained after classical drying of silica-wollastonite gels. Two different silica precursors were used, TEOS and colloidal LUDOX, for composites named TW and LW, respectively. We utilized SAXS experiments, N2 adsorption-desorption, and SEM techniques to determine the textural and structural properties of these porous materials. For both the TW and LW composites, it was shown that a macroporosity and a mesoporosity coexist. We argue that the proportion of macroporosity directly depends on the proportion of wollastonite fillers in the composite. We propose a unique two-stage drying mechanism to explain the formation of macropores. We additionally found that the surface of wollastonite fillers was covered by a dense multilayer packing of silica colloids in LUDOX LW xerocomposites. We believe that these surface-modified wollastonite fillers could improve the carbonation kinetics of wollastonite when used as a precursor for aqueous mineral carbonation, a promising route for safe and durable carbon sequestration.

Nanolaminate membranes made of two-dimensional materials such as graphene oxide are promising candidates for molecular sieving via size-limited diffusion in the two-dimensional capillaries, but high hydrophilicity makes these membranes unstable in water. Here, we report a nanolaminate membrane based on covalently functionalized molybdenum disulfide (MoS2) nanosheets. The functionalized MoS2 membranes demonstrate >90% and similar to 87% rejection for micropollutants and NaCl, respectively, when operating under reverse osmotic conditions. The sieving performance and water flux of the functionalized MoS2 membranes are attributed both to control of the capillary widths of the nanolaminates and to control of the surface chemistry of the nanosheets. We identify small hydrophobic functional groups, such as the methyl group, as the most promising for water purification. Methyl- functionalized nanosheets show high water permeation rates as confirmed by our molecular dynamic simulations, while maintaining high NaCl rejection. Control of the surface chemistry and the interlayer spacing therefore offers opportunities to tune the selectivity of the membranes while enhancing their stability

The Raman modes of α-quartz-type boron phosphate were found to be extremely stable in frequency over a large temperature range from 300–1000 K. In order to determine the origin of this behavior, the material was also studied at high pressure up to 6 GPa. Upon compression, a classical behavior was observed with mode Grüneisen parameters ranging from −0.08(2) to 3.0(1). The present results indicate that the high temperature behavior in this material is an example of an unusual compensation effect between phonon–phonon interactions and implicit contributions due to thermal expansion. Phonon stability is of utmost importance for materials properties that are dependent on it such as dielectric and piezoelectric properties, for example. Boron phosphate belongs to the important class of α-quartz-type piezoelectric materials for which temperature stability is of primordial importance for resonator and sensor applications.

This paper presents an efficient way to measure the curing kinetics and gel point, αgel, in epoxy resins from one single experiment. The epoxy curing reaction is herein monitored using in situ and time-resolved near-infrared absorption spectroscopy (NIR). The curing profiles over different isothermal conditions are in good agreement with DSC. Furthermore, the increase of the NIR absorption bands of aromatic rings (unreactive throughout curing) probe the cure shrinkage, as more and more aromatic rings are localized within the fixed sample volume. Therefore, the gel point is determined using the onset of the aromatic absorption increase. The results are in good agreement with the theoretical gel point, as well as DMA results. This innovative approach enables gelation measurements on epoxy neat resins and film composites with an easy-to-perform, accurate, robust, and versatile method.

To date, aqueous stable graphene flakes solutionscan be obtained by simple REDOX reactions.1–5 Most of the current applications regardinggraphene require ordered nanostructuredcomposites materials. Liquid crystal phases orderingrepresent an opportunity to arrange theminto macroscopic assemblies with long-rangeordering. 1,2 Preparing organized materials andthin films from these dispersions then requires agood control of the liquid crystal ordering duringthe deposition and the drying of the films. As amatter of fact, it turns out that graphene flakeseasily align at high shear.3,4 On the other hand,Graphene Flakes Liquid Crystals (GFLC) exhibita very interesting behaviour at low shear or undersmall displacements, thin films often showspeculiar patterns (such as the periodic texturesshown in Fig.72-72). We have shown how tocreate and stabilize large-sized periodic texturesin GFLC. The patterns have been characterizedunder optical and electronic microscopies. Theirstability can be explained by the competition betweenthe anchoring field of the substrate andthe presence of a yield stress resulting fromthe peculiar elastic and rheological properties ofthe GFLC. Our findings also clarify why longstandinghypotheses on the presence of exoticphases1 at large concentrations are present inthe literature.
References[1] Zakri, C.; Blanc, C.; Grelet, E.; Zamora-Ledezma, C.; Puech, N.; Anglaret, E.; Poulin, P. Philosophical Transactions of theRoyal Society A: Mathematical, Physical and Engineering Sciences 2013, 371, 20120499..
[2] Zamora-Ledezma, C.; Puech, N.; Zakri, C.; Grelet, E.; Moulton, S. E.; Wallace, G. G.; Gambhir, S.; Blanc, C.; Anglaret, E.;Poulin, P. The journal of physical chemistry letters 2012, 3, 2425–2430..
[3] Poulin, P.; Jalili, R.; Neri, W.; Nallet, F.; Divoux, T.; Colin, A.; Aboutalebi, S. H.; Wallace, G.; Zakri, C. Proceedings of theNational Academy of Sciences 2016, 113, 11088–11093..
[4] Zamora-Ledezma, C.; Jeridi, H.; Anglaret, E.; Blanc, C. Orientations and periodic textures in graphene liquid crystals. 27thInternational Liquid Crystal Conference (ILCC2018). 2018..
[5] Xu, Z.; Gao, C. Nature communications 2011, 2, 571.